Ducati, Suzuki and Yamaha Decals and Graphics
Popular decals Homepage Checkout Colours Sitemap Contact us FAQ Honda Models Shipping
Ducati Decals  - Honda Decals  - Kawasaki Decals  - Suzuki Decals  - Yamaha Decals  - Sponsor Logos

Paypal  Payments MasterCard Payments Visa Card Payments Bitcoin Payments

  View Shopping Cart US$0.00
Illustrated Catalog Pages
How to peel decals

Hexis Skintac
Motorbike decals by make
Aprilia Decals
BSA Decals
Ducati Decals
Harley Decals
Honda Decals
Kawasaki Decals
Norton Decals
Suzuki Decals
Triumph Decals
Vespa Decals
Yamaha Decals

Manufacturer Logos
Manufacturer Decals
Sponsor Decals

Other decals and badges
Domed Badges
Graphic Kits
Kanji Decals
Pocket Bike Decals
Racebike Decal Kits
Race Numbers
Signature Decals
Tank Pads
Wheel Rim Decals

Motorcycle Books
Ducati Books
Honda Books
Kawasaki Books
Suzuki Books
Yamaha Books

Our decals fitted
Ducati Customers Bikes
Honda Customers Bikes
Kawasaki Customers Bikes
Suzuki Customers Bikes
Yamaha Customers Bikes

Peeling decals
Fitting decals
Browse our catalog
Honda VF VFR Bikes
Honda CBR 900 Fireblade
Yamaha R1
Yamaha R6
Yamaha R7
Yamaha Racing
Fiat Kit on R6
Fitting your decals
Honda Decal
Suzuki Decal

Privacy Policy All transactions are
Secure Thwate SSL



Honda CBR 1100XX Super Blackbird

Instruction for fitting Decals.

If you have difficulty peeling you decals click here to see how to do this


Fitting Decals Wet method

1.������������ All screen decals must be placed on the inside unless stated otherwise.

2.������������ Fit the decal in a warm environment.

3.������������ Clean the surface where the decal is to be fitted thoroughly with soapy water(ensure that the cleaner does not damage paintwork. it is important that there is no wax or grease on the surface)

4.������������ Place the decal on the surface and hold in place with a piece of masking tape on one edge so that you can still lift the decal from the surface

5.������������ Carefully peel off the backing that is next to the surface that the decal is to be applied to

6.������������ Spray a mild mixture of soap and water on the area the decal is to be applied this will help stop air bubbles and allow you to position the decal accurately

7.������������ Lay the decal onto the surface, slide it into the position you require it and with a credit card, starting at the middle work out all the liquid

8.������������ Leave to dry for 12to 24hours longer if the temperature is lower than 60 degrees

9.������������ Carefully remove the masking tape and the decal backing ensuring the decal does not come off with the backing. Do this slowly.

10.���������� Do not wash the area vigorously for a couple of weeks


Fitting Decals Dry method

6.        For optimum results, surface temperature should be above 50�F and below 90�F. If necessary, move vehicle to a location where the temperature can be within the installation guidelines. You will need a ruler, masking tape, scissors, lint free cloth, a surface cleaner(isopropyl alcohol is recommended) and a slip solution is optional for larger graphics

7.        After determining the location for your graphic, clean the surface with a lint free cloth and cleaner solution. Be sure to turn the cloth several times to insure thorough cleaning and wax removal. After doing this you should get a "squeaky" sensation when lightly dragging your fingers across the surface.

8.        Using small strips of masking tape, locate where the graphic is to be installed. If the graphic has a horizontal edge or reference point, you can use this for measuring the location from a body line or trim moulding. If the decal has a flowing design, you'll have to step back and visually inspect its location to determine if that is where you want it. Once this is done, make measurements from individual points on the design and transfer the locations to the opposite side of your vehicle. (This is the step you need to take your time on, measure from different locations, once the graphic is installed, it cannot be moved).

9.        Place two strips of masking tape (slightly overlapping each other) vertically in the approximate centre of the graphic. This is known as the "hinge" method. This will allow you to install half of your decal at a time.

10.     Remove the masking tape strips from one end of the decal and slowly peel the backing paper away, taking care not to touch the adhesive side of the graphic. Use scissors to remove the backing paper and discard.


To remove a decal

1.������������ Use a heat gun to warm the decal and peel it off gently

2.������������ To remove any additional glue use rubbing alcohol or similar compound (ensure that this does not mark the paintwork)


If you require extra letters due to accidental damage, theft, and vandals or for any reason email me at [email protected] and we will be pleased to help you.


If this product arrives damaged in transit, please repack it into a suitable envelope and return it to us for a replacement. If you send us photos of the decals fitted you will get free shipping on your next purchase.

If you have a problem with the size of a decal email us with the size you need & the year and model of the vehicle

If you need a standard decal or decal setwe do not have, if you provide the dimensions and an image we will make this for your at half price.All decals supplied by us can be clear coated but have an excellent life if they are not.

Copyright 2023(c) xtreemedecals.com